Subject: Re: Problem with Flowscan install
From: Andersson (217andersson-per@telia.com)
Date: Wed Aug 21 2002 - 13:00:09 CDT
I think maybe you upgraded your Perl while installing all flowscan-related tools. Do as follows. Reinstall perl5.6.0 and after that do make clean for all packages installed and then reinstall everything. Per ----- Original Message ----- From: "Nuno Rodrigues" <nuno@ipb.pt> To: "McDonald, Dan" <Dan.McDonald@austinenergy.com> Cc: "flowscan" <flowscan@net.doit.wisc.edu> Sent: Wednesday, August 21, 2002 7:06 PM Subject: Re: Problem with Flowscan install > > > McDonald, Dan wrote: > > >you need to do three makes: > >make > >make install > >make site-perl-install > > > I also had attemped of this form, but i thisk that the problem is from > my perl... :( > However i had installed the RPM rrdtool and rrdtool-devel and the > Flowscan config pass this point. > Now, the problem is with other: > ... > checking for Boulder::Stream... yes > checking for Net::Patricia >= 1.010... yes > checking for ConfigReader::DirectiveStyle... no > configure: error: Must be able to use ConfigReader::DirectiveStyle! > [root@carme FlowScan-1.006]# > > After this, the installation of ConfigReader give the following result: > > # perl -MCPAN -e shell > cpan> install ConfigReader::DirectiveStyle > ... > Writing Makefile for ConfigReaderDirectiveStyle > cp DirectiveStyle.pm blib/lib/DirectiveStyle.pm > cp ConfigReader.pod blib/lib/ConfigReader.pod > cp Spec.pm blib/lib/Spec.pm > cp Values.pm blib/lib/Values.pm > Manifying blib/man3/DirectiveStyle.3pm > Manifying blib/man3/ConfigReader.3pm > Manifying blib/man3/Spec.3pm > Manifying blib/man3/Values.3pm > *** ERROR: unterminated C<...> at line 43 in file Values.pm > *** ERROR: unterminated C<...> at line 80 in file Values.pm > /usr/bin/make -- OK > Running make test > No tests defined for ConfigReaderDirectiveStyle extension. > /usr/bin/make test -- OK > Running make install > Installing /usr/share/man/man3/DirectiveStyle.3pm > Installing /usr/share/man/man3/ConfigReader.3pm > Installing /usr/share/man/man3/Spec.3pm > Installing /usr/share/man/man3/Values.3pm > Writing > /usr/lib/perl5/site_perl/5.6.1/i386-linux/auto/ConfigReaderDirectiveStyle/.packlist > Appending installation info to /usr/lib/perl5/5.6.1/i386-linux/perllocal.pod > /usr/bin/make install -- OK > > cpan> > > What could be the problem? > > Thaks by your help! > Nuno. > > > > >The first one compiles everything > >the second one moves images and libraries to the appropriate places. > >the third one moves perl modules to the appropriate places. > > > > > >Daniel J McDonald, CCIE #2495, CNX > >Lan/Wan Integrator > >Austin Energy > >1.512.322.6739 > >dan.mcdonald@austinenergy.com > > > > > >-----Original Message----- > >From: Nuno Rodrigues [mailto:nuno@ipb.pt] > >Sent: Wednesday, August 21, 2002 9:55 AM > >To: flowscan@net.doit.wisc.edu > >Subject: Problem with Flowscan install > > > > > > > >I'm new with Flowcan and i have a litle/big problem with your instalation. > >When i start to configure Flowscan (./configure), the system give the > >following error message: > >[root@carme FlowScan-1.006]# ./configure > >... > >checking for rrdtool... no > >configure: error: rrdtool not found! > > > >Before this step, i followed with success all previous steps described > >in > >(http://net.doit.wisc.edu/~plonka/FlowScan/INSTALL.html#Software_Requirement > >s). > > > >I have instaled the RRDTOOL like the instructions sugest...: > > > > $ ./configure --enable-shared > > $ make site-perl-install > > > >... > >make[1]: Leaving directory `/root/rrdtool-1.0.39' > >cd perl-piped && make install > >make[1]: Entering directory `/root/rrdtool-1.0.39/perl-piped' > >Installing /usr/share/man/man3/RRDp.3pm > >Writing /usr/lib/perl5/site_perl/5.6.1/i386-linux/auto/RRDp/.packlist > >Appending installation info to /usr/lib/perl5/5.6.1/i386-linux/perllocal.pod > >make[1]: Leaving directory `/root/rrdtool-1.0.39/perl-piped' > >cd perl-shared && make install > >make[1]: Entering directory `/root/rrdtool-1.0.39/perl-shared' > >Files found in blib/arch: installing files in blib/lib into architecture > >dependent library tree > >Installing /usr/share/man/man3/RRDs.3pm > >Writing /usr/lib/perl5/site_perl/5.6.1/i386-linux/auto/RRDs/.packlist > >Appending installation info to /usr/lib/perl5/5.6.1/i386-linux/perllocal.pod > >make[1]: Leaving directory `/root/rrdtool-1.0.39/perl-shared' > >[root@carme rrdtool-1.0.39]# > > > >Pparently, the rrdtool perl modules had installed... > > > >What can e the problem...? > >Thanks in advance by your help! > > > >Nuno. > > > >--- > >................................................................. > > Nuno Rodrigues : nuno@ipb.pt : http://www.ipb.pt/~nuno > > Assistente 2o Triénio : Dep. Informática e Comunicações : ESTiG/IPB > > Coordenador do Centro de Comunicações do IPB > >................................................................. > > > > > > > >-- > >Help mailto:majordomo@net.doit.wisc.edu and say "help" in message > >body > >Unsubscribe mailto:majordomo@net.doit.wisc.edu and say > >"unsubscribe flowscan" in message body > >Archive http://net.doit.wisc.edu/~plonka/list/flowscan/archive/ > > > > > > > > > > -- > ................................................................. > Nuno Rodrigues : nuno@ipb.pt : http://www.ipb.pt/~nuno > Assistente 2o Triénio : Dep. Informática e Comunicações : ESTiG/IPB > Coordenador do Centro de Comunicações do IPB > ................................................................. > > > > > -- > Help mailto:majordomo@net.doit.wisc.edu and say "help" in message body > Unsubscribe mailto:majordomo@net.doit.wisc.edu and say > "unsubscribe flowscan" in message body > Archive http://net.doit.wisc.edu/~plonka/list/flowscan/archive/ > -- Help mailto:majordomo@net.doit.wisc.edu and say "help" in message body Unsubscribe mailto:majordomo@net.doit.wisc.edu and say "unsubscribe flowscan" in message body Archive http://net.doit.wisc.edu/~plonka/list/flowscan/archive/
This archive was generated by hypermail 2b25 : Wed Aug 21 2002 - 13:01:04 CDT